Marine Painting in South Florida: Awlgrip Topsides, Prep and What a Repaint Costs

View Our Recent Work:

Marine painter spraying a glossy navy topcoat on a sportfish yacht's topsides in a covered South Florida paint shed

Paint & Fiberglass · Topsides

Marine painting at a full-service yard means a haul-out, careful fairing, a built-up primer, a sprayed two-part topcoat and a final inspection. The paint is the last day of the job. The weeks before it decide how the finish looks and how long it lasts.

If you searched for marine painting near you, you probably want two answers: who can do the work properly, and what it will cost. This page covers both for yacht and sportfish owners from Miami up the coast to Palm Beach and Stuart. It is about topsides and exterior paint only. Bottom paint and cosmetic gelcoat work have their own pages, and we point to them where they fit.

How to use this pageNeed a number first? Jump to the cost section, then read the prep section to see why quotes differ.Planning dates? The schedule timeline shows how long the boat is out of the water.Not sure paint is the right fix? The topsides, bottom and gelcoat comparison sorts that out.

Key Takeaways

  • 01

    Topsides only — This page covers hull sides and exterior paint; bottom paint and gelcoat repairs are separate jobs.

  • 02

    Prep sets the result — Most of the hours go into fairing and primer, which is why quotes for the same boat differ.

  • 03

    Budget per foot — Hull sides run about $150 to $350 per foot here; a full exterior can reach $700 to $1,000.

  • 04

    Weather rules the spray day — The hull must stay at least 5°F above the dew point, so crews plan around humidity.

  • 05

    Gentle care — Wash with mild soap, rinse well and never use abrasive compounds on a polyurethane finish.

What Marine Painting Covers at a Full-Service Yard

In short, a professional topsides repaint is a sequence: haul the boat, read the hull, fair it smooth, build primer, spray the topcoat, then cut and buff any flaws. Topsides means the hull sides above the waterline, from the boot stripe up to the rubrail. Bottom paint is the antifouling below the waterline, and that is a separate job with a separate budget.

At Mazza Marine Yacht Brokerage and Refit, we coordinate trusted paint and fiberglass crews in the Miami area, from efficient bottom work to full Awlgrip finishes. You can see the wider range of our paint, hull and gelcoat services on the main service page.

The boundary matters for your wallet. A topsides quote should never hide bottom work inside one figure. If you need the antifouling side priced too, read what a full bottom paint job runs in this market and ask for the two jobs on separate lines.

Definition

Two-part polyurethane — A paint made of a base and an activator that react to form a very hard, glossy film. Awlgrip and Alexseal are the best-known yacht systems. Once mixed, the paint has a limited working time and must be sprayed under controlled conditions.

Awlgrip, Alexseal and the Two-Part Systems Used on Yacht Topsides

Most yacht topsides in South Florida are finished in one of two families of two-part polyurethane. Both can look superb. The real differences are how forgiving they are to apply and how easily a damaged spot can be blended later.

Owners often ask whether to paint at all or keep the original gelcoat. That is a fair question on a younger boat, and the Awlgrip versus gelcoat trade-offs are worth reading before you commit. Paint wins on depth of gloss and stain resistance. Gelcoat wins on impact toughness and easy spot repair.

Common topsides finishes compared

SystemSheenTypical life in Florida sunRepairability
Awlgrip topcoatDeep, high glossOften 8 to 10 years with careful washingHard to spot-blend; damage often means a whole panel
Awlcraft 2000High glossGood, and easier to refresh with polishingCan be buffed and polished, so small flaws are easier to fix
Alexseal topcoatHigh glossComparable to Awlgrip in the fieldDesigned to be easier to repair and blend
Original gelcoat (restored)Good gloss after compoundingLong life, but oxidizes without regular careEasy to spot-repair and colour match

Prep Is the Job: Fairing, Primer Build and Why It Sets the Finish

Here is the part most quotes skip over. On a topsides repaint, most of the hours go into preparation, not spraying. A high-gloss coat works like a mirror. Every dip, ridge and sanding scratch underneath shows through once the sun hits the hull at a low angle.

That is why two quotes for the same boat can be far apart without either painter being dishonest. One may assume a sound hull that needs a light sand and primer. The other may have found soft spots, old filler and fastener bleed that all need work first.

Reading the Hull Before Any Paint Is Ordered

A good painter starts by looking, tapping and measuring. They check the old coating for cracking and lifting, sound the hull for hollow spots, and look along the topsides for waves in the surface. Old screw holes from removed hardware, canvas snaps and electronics all need to be found and filled.

If the inspection turns up cracked or wet fiberglass, paint has to wait. Structural problems go to fiberglass upgrades and damage repair first, because a coating cannot add strength. Small chips and dock rash on a hull that will not be painted are better handled by colour-matched gelcoat repair instead.

Fairing Compounds, Primer Coats and Sanding Schedule

Fairing means filling low spots with a light, sandable compound, then long-board sanding until the surface is true. It is slow, skilled work, and it is often repeated two or three times on an older hull. Rushing it is the most common reason a new finish looks wavy.

Next comes a high-build primer. It fills fine scratches and gives the topcoat an even base to bond to. Painters build it in several coats, sanding between them with finer and finer paper. Each layer is measured for thickness, usually in mils, which are thousandths of an inch.

Masking and hardware come last. Removing rails, cleats and fittings costs more than taping around them, but it gives cleaner edges and fresh bedding. That single choice explains many of the gaps between a low bid and a high one.

What a Repaint Costs in South Florida

Most yards quote exterior paint per linear foot of the boat’s length, then adjust once someone has seen the hull. South Florida labor tends to sit toward the top of national ranges. The figures below are planning ranges for this market, not bids.

$150–$350

Hull sides only, per linear foot

South Florida market ranges, 2026

$200–$400

Hull sides plus boot and cove stripes, per foot

South Florida market ranges, 2026

$300–$450

Decks and superstructure, per foot

South Florida market ranges, 2026

$700–$1,000

Full exterior, keel to flybridge, per foot

South Florida market ranges, 2026

On a 50-foot yacht, hull sides alone come to roughly $7,500 to $17,500. A full exterior with repairs folded in lands nearer $35,000 to $50,000. The paint itself is a small share. Labor for sanding, fairing and masking makes up most of the invoice.

For a deeper breakdown by scope, see what it costs to paint a boat, line by line. If you already know you want Awlgrip, the guide to Awlgrip paint job pricing by yacht size runs the numbers for 40, 60 and 80 foot hulls.

Whatever the size, ask for an itemized scope. It should name the primer system, the number of fairing passes budgeted, the coat count and any hourly allowance with its rate. A single bottom-line figure tells you very little.

Shed Time, Weather Windows and the Realistic Schedule

Florida weather shapes every paint schedule. High humidity and afternoon storms are hard on a fresh topcoat, so most serious work happens under cover. The Awlgrip topcoat technical data sheet sets the limits plainly. Air temperature should sit between 55°F and 105°F, and the hull surface must stay at least 5°F above the dew point.

That dew point rule is the one that bites in South Florida. On a muggy evening, moisture can settle on a warm hull and dull the gloss overnight. Crews plan spray days around it, which is why a good painter will sometimes wait a day rather than spray into bad air.

Week 1

Haul-out and inspection

The boat comes out, hardware is listed and the hull is sounded, measured and photographed.

Weeks 1–3

Strip, repair and fair

Old coating is sanded back, damage is repaired, and fairing passes bring the surface true.

Weeks 2–4

Primer build

Primer goes on in several coats, sanded between each, until the base is smooth and even.

Spray days

Topcoat

Most spray work is done in about three coats, laid on during a clean, dry weather window.

After spray

Cure, buff and refit hardware

The paint hardens over about two weeks at room temperature. Flaws are cut and buffed, then hardware goes back on.

As a rough guide, hull sides alone usually take two to three weeks in the yard. Adding stripes stretches that to three or four. Decks and superstructure take four to six weeks, and a full exterior can run eight to fourteen. Plan the work around your season, not the other way round.

Topsides Paint vs Bottom Paint vs Gelcoat Restoration

These three jobs often get lumped together under marine painting, but they solve different problems. Knowing which one you need saves money and stops a quote from drifting.

QuestionTopsides paintBottom paintGelcoat restoration
What it is forGloss, colour and protection above the waterlineStops growth on the hull below the waterlineBrings back the original finish or fixes local damage
Typical productsAwlgrip, Awlcraft 2000, AlexsealAblative or hard antifoulingMatched gelcoat, compound and polish
How oftenMany years between repaintsUsually every one to two seasonsAs needed for chips, cracks or fading
Haul-out neededYes, for a sprayed finishYesNot always for small repairs

If growth below the waterline is your real problem, start with the guide to ablative and hard antifouling coatings. If your topsides are faded but sound, a gelcoat restoration may buy several more years before a full repaint makes sense.

Caring For a New Finish: Wash-Downs, Wax and What Kills a Topcoat

A new topcoat is tough, but the wrong care can shorten its life by years. Awlgrip’s finish care guidance is clear on the basics. Wash often with a mild, non-abrasive soap and soft mitts, then rinse well with fresh water.

Abrasives are the main enemy. Rubbing compounds, scrub pads and gritty cleaners wear away the gloss layer, and on Awlgrip they can void the limited warranty. Plain wax does little harm, but it adds no real benefit and can yellow over time. A sealer made for the paint is the better choice.

Watch what touches the hull, too. Most teak cleaners contain acids that can stain a painted surface, so protect the topsides when the deck is cleaned. Wet fenders and covers left pressed against the paint can also trap moisture and cause trouble.

Frequently Asked Questions

Q.What does marine painting actually include beyond the topcoat?
A proper job includes the haul-out, hull inspection, removal or masking of hardware, repairs, fairing, several coats of primer with sanding in between, the sprayed topcoat, and a final cut and buff. The topcoat itself is only a few days of a job that often runs for weeks.
Q.What is the average cost to paint a boat in South Florida?
Hull sides alone usually run about $150 to $350 per linear foot, so roughly $7,500 to $17,500 on a 50-footer. A full exterior from keel to flybridge, with repairs, can reach $700 to $1,000 per foot. Condition and scope move the number more than the paint brand does.
Q.Is it cheaper to paint a yacht or wrap it?
A vinyl wrap usually costs less up front, but it is a film laid over the surface, not a coating bonded to it. It will not hide an uneven hull, and it has a shorter working life than a two-part paint. For a long-term finish on a large yacht, paint is usually the better value.
Q.How long does an Awlgrip topsides job take from haul-out to splash?
Hull sides alone usually take two to three weeks. Adding boot and cove stripes stretches that to three or four weeks. Decks and superstructure take four to six weeks, and a full exterior can take eight to fourteen weeks.
Q.How long should a professional Awlgrip finish last in Florida sun?
With good prep and gentle care, an Awlgrip finish often keeps its gloss for eight to ten years. Abrasive polishing, harsh cleaners and poor prep can cut that short. Regular fresh-water rinses after each trip help a great deal.
Q.Can topsides be painted in the water or does the boat have to be hauled?
Small touch-ups can sometimes be done afloat, but a full sprayed finish needs the boat hauled and the work done under cover. That gives the crew safe access, steady conditions and control over dust, humidity and dew.
Q.What is the difference between topsides paint, bottom paint and gelcoat restoration?
Topsides paint is the glossy finish above the waterline. Bottom paint is antifouling that keeps growth off the hull below the waterline. Gelcoat restoration brings back or repairs the boat’s original outer skin without painting it.

Mazza Marine

Schedule a topsides estimate

Tell us about your boat, its length and what the topsides look like today. We will help you scope the job and line up the right paint crew for it.

Text or Call 954-330-9653


Schedule Appointment


Get your yacht value Estimate

"*" indicates required fields

This field is for validation purposes and should be left unchanged.